Nextel is making deals with SMR operators–that have fully built and utilized repeater systems. Licenses are being pulled from SMRs that aren’t actually fully built and on-air! You may feel a little non-committal to putting a full spec trunked system on the air. Particularly in rural locations with low POP, we want to maximize ROI.
We provide repeater systems (1 to 20 channels), a legal system fulfilling the mandate in spirit and letter. We provide late model, turnkey refurbished repeater systems meeting and exceeding FCC/IC specifications. This equipment is legitimately obtained from other SMR operators who have already transitioned off of 800⁄900 MHz LTR as their customers grab up Nextel phones.
Nextel is making rapid advances and expansion in the Midwest in particular. Soon Nextel will be knocking on your door, SMR owners–is your system ready for inspection? Is your SMR license built up, or will Nextel grab your license from you? You would be left with nothing, no recourse because you didn’t fulfill your FCC mandate. From our side, the repeaters cost thousands of dollar each because most SMRs are hanging on for their Nextel buyout.
While you might see on eBay late 1980s SMR 800MHz subscriber mobile units that are selling for less than $50, and PRO-2004 scanners from the mid-1980s selling for $100 or so, we provide fully-checked and guaranteed systems. You don’t want embarrassment on Nextel’s judgment day for your SMR license!
making an 800MHz/900MHz repeater from scanners and mobile radios
Since we’re making a multi-channel trunked repeater from salvage parts, we have to consider filtering and connections.
Unlike lower frequency bands where repeaters like GR300 or the new R1225 repeater that are essential refitted mobile radios for transmit and receive, no 800 MHz subscriber receiver is readily retuned to the 806-821 MHz mobile transmit band. I thought about hacking around retuning filters, but going down in frequency is harder than going up. Also I’d have to hack the CPU. The easier plan is take the 1980s scanners being dumped on eBay as people pickup TrunkTracker scanners. For example, the PRO-2004 has specified 0.5 μV sensitivity. Since we need a receiver distribution amplifier anyway, just leave 6 dB less padding than before–problem solved!
For filtering, that will be part of the distribution amplifier–it will filter out the strong transmit signal on the separate antenna as well as any lower frequency signals (FM/TV/UHF/VHF) and any higher frequencies (AMPS 850 MHz). Given the location there shouldn’t be too many strong in-band signals, though overloading is possible within a km or so of the site. If that became an issue I could put a cavity filter on that channel, again from eBay. But for simplicity let’s stick with the receiver distribution amp 806-821 MHz filter.
The audio connection is made at the discriminator tap as I need the DC-coupled baseband to retrieve LTR data. The volume control is just left all the way down to avoid bothering other workers in the radio room. I leave the scanner speaker connected for basic diagnostics.
I use the EF Johnson 8600-series radio–get the full feature model with up/down arrows, not the single button model as you need talkaround! I set the radios to 10 Watts transmit power so that they can handle the duty cycle, and to help reduce thermal cycling stresses. I program each radio to a single channel, talkaround on the repeater output frequency. I bypass the microphone jack so that I get the full non-pre-emphasized DC response to the modulator. The LTR waveform is a little sloped but test radios seem to decode it OK. I’ll have to test under real-life fluttery conditions to be sure I don’t need further measure to correct the skew of the LTR waveform.
These are not free but they are on eBay. Any 800 MHz SMR combiner is fine.
receiver distribution amplifier
This has three parts:
- 806-821 MHz combline bandpass filter
These tend to come in multiples of four as it’s easier to cascade that way as per Chip of Angle Linear. I managed to find a used one but in the future I would consider Angle Linear for even higher performance with his 0.7 dB NF amplifiers. He spun off his company from NASA!
These are not particular to the transmitters, but can be particular to each other. EF Johnson and Uniden use distinct backplane signaling. Others are switchable via jumper. Uniden doesn’t need a terminator while EF Johnson does need a 50 ohm terminator. In this case, I got some gently used IDA RLC panels from a system that had downsized.